初级建模教程--------NOKIA3310手机建模！
data/attachment/forum/2004-1/2004151138431409.jpg<br>如图建立一个长方体，段数分别为9、4、4。data/attachment/forum/2004-1/20041511382424048.jpg<br>把长方形塌陷为可编辑网络物体，并调整点，如图所示！data/attachment/forum/2004-1/20041511384866433.jpg<br>选择要做为按钮的12个点，使用chamfer工具。并调整点的位置，如图所示！data/attachment/forum/2004-1/20041511391179375.gif<br>选择按钮两边的边，同样使用chamfer工具。data/attachment/forum/2004-1/20041511393178414.gif<br> 如图，将两边的点塌陷焊接！
data/attachment/forum/2004-1/20041511403584897.gif<br>如图，选择边工具cut进行切线！data/attachment/forum/2004-1/20041511405713003.gif<br>data/attachment/forum/2004-1/20041511411251422.gif<br>data/attachment/forum/2004-1/20041511412772537.gif<br>如图，切线！data/attachment/forum/2004-1/20041511414641688.gif<br>如图，切线！data/attachment/forum/2004-1/20041511421740930.gif<br>如图，将所选择的点向上拖起！data/attachment/forum/2004-1/20041511423436327.gif<br>data/attachment/forum/2004-1/20041511424991571.jpg<br>加入修改命令meshsmooth设为1级光滑！并选择显示最终结果命令，参照图例调整侧面点的位置！使之与参考图片相似,如图！
data/attachment/forum/2004-1/2004151143934179.jpg<br>选择按钮的面，进行向下挤压data/attachment/forum/2004-1/20041511433314738.jpg<br> 选择两个面周围的点如图增加权重值！
选择按钮的面，进行向上挤压！
data/attachment/forum/2004-1/20041511441380449.jpg<br>将按钮周围的点选中，并将他们的权重值增加！使边缘的棱角硬化！data/attachment/forum/2004-1/20041511442727550.jpg<br>data/attachment/forum/2004-1/20041511445119327.jpg<br>再选择这部分面向上挤压！data/attachment/forum/2004-1/2004151145578993.jpg<br>将这部分面周围的点选中，增加权重值！如图所示！data/attachment/forum/2004-1/20041511451920799.jpg<br>data/attachment/forum/2004-1/20041511453189178.jpg<br>data/attachment/forum/2004-1/20041511454154543.jpg<br>data/attachment/forum/2004-1/20041511455238531.gif<br>data/attachment/forum/2004-1/2004151146411614.gif<br>data/attachment/forum/2004-1/20041511461961119.gif<br>data/attachment/forum/2004-1/20041511463370968.gif<br>data/attachment/forum/2004-1/20041511464796374.gif<br>选择中两个要做为按钮部位的面向下再向上进行挤压！data/attachment/forum/2004-1/20041511471075615.jpg<br>选择两个面周围的点如图增加权重值！
data/attachment/forum/2004-1/20041511473281712.gif<br>选择两个面周围四个角的点再次增加权重值！
data/attachment/forum/2004-1/20041511475932312.gif<br> 如图选择顶部的一条线，使用Chamfer工具！data/attachment/forum/2004-1/20041511484823025.gif<br>选择这部分面进行挤压！
data/attachment/forum/2004-1/2004151149731484.gif<br>增加为2级光滑，查看此时状态！data/attachment/forum/2004-1/20041511492236648.gif<br>再将现在的状态塌陷为可编辑网格物体！data/attachment/forum/2004-1/20041511494628161.gif<br>建立五个小圆柱体！按顺序摆放并塌陷为一个物体！并进行布尔运算！data/attachment/forum/2004-1/2004151150289805.gif<br>最后效果data/attachment/forum/2004-1/20041511502086784.gif<br> 高，实在是高，你用的就是这个手机啊 值得学习 HOHO！ 绊住辛苦谢谢 很不错啊~~ 有没有书
好累啊
页:
[1]
2
